[PD] Comport problem with Arduino: 13 is coming in as 10

[Christof Ressi]

> > So, neither the OS nor the Pd or [comport] version seem to make any
> difference.

check my last two mails, I think this is macOS/Linux issue. can you try my fix?

> Gesendet: Dienstag, 14. Mai 2019 um 13:07 Uhr
> Von: "Ingo" <ingo at miamiwave.com>
> An: 'Ingo' <ingo at miamiwave.com>, "'Roman Haefeli'" <reduzent at gmail.com>, adrcki at gmail.com, itensimon at gmail.com, pd-list at lists.iem.at
> Betreff: Re: [PD] Comport problem with Arduino: 13 is coming in as 10
>
> I just tested this on another OS.
>
> My older system that did it was a relatively old Ubuntu 11.10 still using
> the older [comport] object with Pd-Extended.
> Now I tested with a rather new Debian (9.5 / 32bit) and a recent Pd (0.48)
> with the latest [comport] object.
>
> Both behave the same way.
>
> If I send a MIDI program change from my EWI to the USB (-MIDI) input I get
> the correct program number.
> If I use the MIDI Din cable going from the EWI into my Arduino MIDI
> interface I get MIDI program #11 instead of #14 (counting from 1-128!).
> Still the number 13 gets replaced with 10.
>
> This time the Arduino is a Arduino Micro and not a ProMicro with a different
> programming.
>
> So, neither the OS nor the Pd or [comport] version seem to make any
> difference.
>
> Ingo
>
>
> > -----Original Message-----
> > From: Ingo [mailto:ingo at miamiwave.com]
> > Sent: Tuesday, May 14, 2019 12:36 PM
> > To: 'Ingo'; 'Roman Haefeli'; pd-list at lists.iem.at
> > Subject: RE: [PD] Comport problem with Arduino: 13 is coming in as 10
> >
> > Sorry, this was meant to be:
> > Carriage Return is 13. Line Feed is 10 (not 0x10).
> >
> > > -----Original Message-----
> > > From: Pd-list [mailto:pd-list-bounces at lists.iem.at] On Behalf Of Ingo
> > > Sent: Tuesday, May 14, 2019 12:31 PM
> > > To: 'Roman Haefeli'; pd-list at lists.iem.at
> > > Subject: Re: [PD] Comport problem with Arduino: 13 is coming in as 10
> > >
> > > The strange thing is that I'm using 2 Arduino ProMicro.
> > >
> > > Sometimes one does it and the other one is fine. Next time both of
> > > them do it and next time none of them.
> > > It's completely unpredictable. The same Arduino sends the same data
> > > that gets interpreted differently when I reopen Pd.
> > > So I wouldn't blame the Arduino in this case. I don't expect it to
> > > send different values upon reopening Pd.
> > > (I'm not sure if I did a hardware restart in between - I'll have to
> > > observe
> > > this.)
> > >
> > > However, the Pd programming hasn't changed either ...
> > > I know there is some sort of modem code that replaced 13 with 10.
> > > Carriage Return is 13. Line Feed is 0x10.
> > > In some cases The Carriage Return is either followed or even replaced
> > > by Line Feed.
> > > It looks like this is happening here.
> > >
> > > The question is: How can I control this type of Carriage Return
> behavior?
> > > I don not my Arduino to be handled as an old modem ...
> > >
> > >
> > > > I have tried Serial.write(13) and Serial.print((char)13) and they
> > > > both output 10 in Pd. The work-around I have figured to this is to
> > > > write a second byte after every value I send, and in case of sending
> > > > a 13, send a unique value to this second byte, so that Pd knows it
> > > > should be receiving a 13. It's double the load but in most cases it
> > > > shouldn't be a problem, especially when writing raw bytes with
> > Serial.write().
> > >
> > > I have already a bunch of units out with the same hardware.
> > > So changing the programming on the Arduino is not necessarily the best
> > > choice.
> > >
> > > Ingo
> > >
> > >
> > > > -----Original Message-----
> > > > From: Pd-list [mailto:pd-list-bounces at lists.iem.at] On Behalf Of
> > > > Roman Haefeli
> > > > Sent: Tuesday, May 14, 2019 11:38 AM
> > > > To: pd-list at lists.iem.at
> > > > Subject: Re: [PD] Comport problem with Arduino: 13 is coming in as
> > > > 10
> > > >
> > > > On Tue, 2019-05-14 at 10:00 +0100, Alexandros wrote:
> > > > > On 14/5/19 9:45 p. ., Roman Haefeli wrote:
> > > > > > Hi Ingo
> > > > > >
> > > > > > On Tue, 2019-05-14 at 07:38 +0200, Ingo wrote:
> > > > > > > I'm getting number 10 instead of 13 from my adruino.
> > > > > >
> > > > > > This sounds somehow familiar to me, but I can't recall the exact
> > > > > > details of the issue nor am I able to find something about it on
> > > > > > the web.
> > > > > >
> > > > > > Have you ruled out any other source besides [comport]?  Can you
> > > > > > print the data with some other tool to make sure that the
> > > > > > Arduino is not messing up the bytes 10 and 13? If it indeed
> > > > > > [comport] is the culprit, then it should be quite easy to fix,
> > > > > > but then again there we probably would find code that does the
> > > > > > translation. I am not sure such code exists.
> > > > >
> > > > > I have been having the same issue for quite some time now, and
> > > > > have posted it in this list in the past.
> > > >
> > > > Have you ruled out any other culprit? Have checked what is sent with
> > > > some means other than [comport], for instance with the Arduino IDE?
> > > > I don't have an Arduino at hand, so I don't know the exact
> > > > procedure, but maybe there is a way to print data as hex values or so.
> > > >
> > > > Roman
> > >
> > >
> > >
> > >
> > >
> > > _______________________________________________
> > > Pd-list at lists.iem.at mailing list
> > > UNSUBSCRIBE and account-management ->
> > > https://lists.puredata.info/listinfo/pd-list
>
>
>
>
>
>
> _______________________________________________
> Pd-list at lists.iem.at mailing list
> UNSUBSCRIBE and account-management -> https://lists.puredata.info/listinfo/pd-list
>